Search: Advanced search
 
Printable version 
Categories Categories
Shop by Brand
Paints & Stains
Painting Tools
Paint Remover & Strippers
Solvents/Cleaners
Patching Materials
Tapes & Adhesives
Paint Sprayers & Accessorios


Bestsellers Bestsellers
1. UGL 01908 DRYLOK ETCH SIZE:12 OZ.
2. UGL 27513 DRYLOK WHITE LATEX BASE WATERPROOFER READY MIXED SIZE:1 GALLON.
3. UGL 30507 DRYLOK GRAY MASONRY CRACK FILLER CARTRIDGE SIZE:10.5 OZ. PACK:10 PCS.
4. UGL 22113 DRYLOK CLEAR MASONRY TREATMENT LATEX BASE SIZE:1 GALLON.
5. UGL 00924 DRYLOK FAST PLUG SIZE:10 LBS.


Manufacturers Manufacturers
3M
Absolute Coatings
Advance Protective Products
Akzo Nobel Paints LLC
Allway Tools
American Safety Razor
ASM
Cabot Stain
Convenience Products
Daich Coatings

Other manufacturers...


Special Special
Gift certificates


Help Help
Contact us
Privacy statement
Terms & Conditions
Sitemap
About Us
Tips for Painting

Paint Store :: Shop by Brand :: Drylok :: UGL 20715 DRYLOK WHITE OIL BASE MASONRY WATERPROOFER READY MIXED SIZE:5 GALLONS.

UGL 20715 DRYLOK WHITE OIL BASE MASONRY WATERPROOFER READY MIXED SIZE:5 GALLONS.
UGL 20715 DRYLOK WHITE OIL BASE MASONRY WATERPROOFER READY MIXED SIZE:5 GALLONS. 

DRYLOK® OIL BASE MASONRY WATERPROOFER
Formulated for waterproofing all interior, exterior, above or below grade masonry walls, cinder and concrete blocks, stucco, brick, retaining walls, basements, concrete swimming pools and foundations. No pre-mixing or pre-wetting necessary.

  • Withstands 10 pounds of hydrostatic pressure, greater than a wall of water 22 feet high.
  • Breathable film - does not trap moisture in masonry.
  • Contains synthetic rubber and Portland cement
  • Applies easily with brush and/or roller straight from the can - no pre-mixing or pre-wetting
  • Performance conforms to Fed. Spec. TT-P-1411-A

 

DESCRIPTION
Oil Base DRYLOK Masonry Waterproofer is a ready-mixed masonry waterproofing paint specially formulated to waterproof interior, exterior, above or below grade masonry walls. Ideal for use on cinder and concrete block, poured concrete walls, stucco, brick, retaining walls, basement walls, birdbaths and fishponds. Not for use on floors.

SURFACE PREP
Masonry surfaces must be clean and free from dirt, dust, grease, oil, form release compound, frost or paint. Patch all holes or cracks with DRYLOK Fast Plug, a fast setting hydraulic cement, and smooth the patch evenly with the surface around it. Check the joint where the floor and wall meet and fill any breaks with DRYLOK Fast Plug. EFFLORESCENCE, a white, powdery, crystal-like deposit visible on the masonry surface must be removed. DRYLOK ETCH or muriatic acid, used according to manufacturer’s directions, are effective efflorescence removal agents. All masonry surfaces are subject to occurrences of efflorescence. Containing synthetic rubber and Portland cement, this tough, alkali-resistant coating may be applied on slightly damp surfaces but best results are obtained when applied on dry surfaces.

APPLICATION
STIR THOROUGHLY BEFORE AND DURING APPLICATION. DO NOT THIN. Paint only when air and surface temperatures are 50°F or higher. Apply DRYLOK Masonry Waterproofer directly on bare masonry. For best waterproofing results, wait for a dry (rain-free) period before application. Apply first coat with a DRYLOK BRUSH or good quality nylon bristle or fiber brush, working the WATERPROOFER into the pores of the masonry - avoid excessive brushing (see COVERAGE). APPLY TWO COATS. Allow 12 hours drying time between coats. The second coat may be applied by brush, roller or spray.

COVERAGE
On rough, porous masonry apply at the rate of 75 sq. ft. per gallon for the first coat and up to 125 sq. ft. per gallon for succeeding coats. On dense, smooth surfaces, apply at the rate of 100-125 sq. ft. per gallon for the first coat and up to 125 sq. ft. per gallon for succeeding coats.

CLEAN-UP
Clean application tools with paint thinner immediately after use.

IMPORTANT
If leaking is still present after two coats, it indicates that pores or pin holes are still open. These areas should be painted again. When painting the inside of concrete fish ponds and water tanks, allow DRYLOK to dry one week before filling with water. Let stand full for 48 hours then drain. Allow surface to dry 48 hours and refill. This procedure will control the alkalinity content. If desired, a high quality latex paint can be applied over DRYLOK Masonry Waterproofer after 30 days for decorative purposes.

 
   

  47%

Details
 
SKU 7994120715
Quantity in stock 1000 item(s) available
Weight 97.00 lbs
Retail Price: $255.98
Our Price: $134.39

Options
 
Quantity

Add to cart
        


 

Send to friend
Your name: *
Your e-mail: *
Recipient's email: *

Type the characters you see in the picture. (If you do not see any picture here, please enable images in your web browser options and refresh this page):

Get a different code
The code is case-sensitive and must be entered exactly as above.

Send to friend
 

Recommended products list
Customers who bought this product also bought the following products:  

 
 

Your cart Your cart
Cart is empty
 

View cart
Checkout
Orders history


Authentication Authentication
Username

Password

Log in 
Register 
Recover password

If Javascript is disabled in your browser click here


News News


 


Popular Categories

Tapes

Spray Paint

Paint Brushes

Paint Tools

Caulk and Sealants

Paint Remover & Stripper

Hand Tools

Interior Paint

Exterior Paint

 

Popular Brands

ZAR

Valpar

Cabot

DAP

3M

ASM

 

Hammerite

Modern Masters

 

Best Seller Products

Duct Tape

Black Paint

White Paint

Blue Paint

Red Paint

Dap Plus

Chalk Board Paint

Gold Paint

Aluminum Paint

 
 

We accept major credit cards

credit cards logo
 
Home | Store | About Us | Search | Terms & Conditions | Privacy Statement | Contact Us | Directory | Site Map | News | Paint Store Blog
 
SEO by site SEO
 
 

CONNECT WITH US
Copyright 2005-2015 Paint Store - All Rights Reserved