Paint Store :: Shop by Brand :: XIM :: XIM 11445 400W ES VOC COMPLIANT SPRAY WHITE PRIMER SEALER BONDER SIZE:16 OZ. SPRAY.

XIM 11445 400W ES VOC COMPLIANT SPRAY WHITE PRIMER SEALER BONDER SIZE:16 OZ. SPRAY.

XIM 11445 400W ES VOC COMPLIANT SPRAY WHITE PRIMER SEALER BONDER SIZE:16 OZ. SPRAY. 

400W ES White: Product Number 1144
Solvent Born, Bonding Primer Sealer, VOC: less than 100 g/l

• Meets California VOC Rules for Primers

• Properties of both a primer and an adhesive

• Makes paint stick to tough-to-paint surfaces, including ceramic tile, porcelain, glass, Formica and melamine laminates, PVC, fiberglass, many plastics, aluminum, many metals, wood

• Very fast drying

• Tintable to pastel colors with universal tint colors

• Interior / Exterior applications

• Top coat with oil-alkyds and latexes in 60 minutes

Product Description: 400W ES White is an ultra-premium solvent based primer/sealer/bonder developed to meet 100 g/l VOC limits and solve many paint bonding problems. It provides excellent adhesion, sealing and bonding on many hard-to-coat surfaces. Clean and dull paintable surfaces may not need sanding, but sanding or dulling the surface is required on hard, glossy surfaces for maximum adhesion. 400W ES White can be used for both indoor or out-door applications and can be used with either oil/alkyd or latex topcoats. Not recommended under with strong solvent topcoats such as lacquers or two component epoxies or urethanes.

Product Use: Ideal prime coat for Wood, Hardboard, Plaster, Glass, Tile, Fiberglass, and Some Plastics. Always test a small area first for adhesion and topcoat compatibility first. Not recommended for polypropylene or polyethylene. Also, not recommended for tubs, sinks or showers where hot or continuous water contact occurs. XIM’s Tile DOC is recommended for these surfaces. It will also bond to ferrous and non-ferrous metals. Note: * When extra rust protection is desired, use a rust inhibiting primer. (XIM 360 or XIM Corrosion Control) On extremely porous surfaces or on wood that is known to cause staining, a second coat may be needed prior to application of the top coat.

Product Preparation: Always open can carefully. Apply directly from the can, no thinning required. Do not add extra solvent. If tinting is desired, use universal or industrial tinting colors, not to exceed two (2) ounces per gallon.
It is a thin product and can settle. Shake or mix well before use Note: A dark, solvent layer can form at the surface during storage. This will mix in easily. Note: The container lid employs a gasket to prevent evaporation of the solvent. When less than the full container has been used, careful resealing with the gasket in position is important to prevent solvent evaporation during storage.

Product Storage: One year at temperatures not to exceed 120 F.

Surface Preparation: Be sure the surface is clean and dry, free from dust, grease, wax, oil, loose paint, dirt and other surface contaminants. The first step is to clean with an abrasive detergent, rinse well and allow to dry. For very hard, glossy surfaces, dulling the surface with a carbide sandpaper is necessary for best adhesion. On ceramic surfaces use XIM’s Etch-I-M etching cream to chemically dull the surface. Solvent wiping the surface with XIM GONTM Solvent Cleaner, XIM GON20 Water Based Cleaner or xylene is also recommended. Do not use mineral spirits, turpentine or any oily cleaning solvent.

Application Information:
Spraying:

  Tip Size Pressure Equipment Mfg.
Airless Spray 0.011 to 0.015 Less than 1500 PSI All Mfg.
HVLP Spray 9 Cap 8 PSI Spraytech, Accuspray, tec.

When spraying, apply a light, but wet mist coat followed by a second light to medium coat. Thin film application is desired.

Brushing: Use a natural bristle brush. Use a China Bristle/Nylon fiber blend brush (varnish style). An example is the Wooster Advantage 4734. Use a China Bristle/Nylon blend sash brush. An example is the Wooster Advantage 4732. These brushes are used with varnishes and other thin viscosity, solvent based products like urethanes and lacquers. The Foam Brushes will swell, but can be used with 400W ES. If using a Foam Brush, make sure the adhesive used to hold the foam together, is not affected by the solvents in the 400W ES. An examples is the Wooster Foam King 3 inch B3102, and it works well.

Rolling: Use a short nap roller cover such as a 1/4 inch mohair cover designed for epoxies, urethanes and smooth surfaces. An example is the Wooster R 209. Also, use a 3/16 inch nap , shed resistant woven fabric cover designed for varnishes and enamels. An example is the Wooster RR-641 Pro/Dooz.. The 3/16 inch foam roller cover, Wooster R-265 Pro Tiz which is designed for all paints did not swell in tests. Always make sure the roller cover adhesive is not affected by the 400W ES solvent. Once a compatible brush or roller is identified, use the following procedure:
1. Wet the brush or roller in the 400W ES
2. Work out the excess in the roller tray or on the inside edge of the can
3. Use light pressure when applying (heavy pressure could cause spatter or runs)
4. As you brush or roll, the 400W ES will thicken and become very workable.
Air and surface temp. should be between 50°F and 90°F. It will dry to touch very quickly (20 to 30 min). A measurement of 1.0 to 1.7 mils wet will give the recommended dry film of between 0.75 to 1..25 mils respectively. One gallon will cover between 650 and 750 square feet per mil depending on film thickness and porosity of the surface. The topcoat can be applied in 2-3 hours. Thicker films can remain tacky for about 24 hours but will generally harden after 48-72 hours. Full cure is generally in 7-14 days. (Will depend on temperature and film thickness). NOTE: When the topcoat is a deep, heavily tinted custom color or a Dry Fog top coat, allow the 400W ES White to dry for 24 hours before applying the topcoat. When 400W ES is applied over existing paints and finishes, it may soften or wrinkle the finish. Always test a small area, first, for compatibility. Flexible seams or caulks may cause cracking or loss of adhesion when coated with 400W ES. Not recommended for 100% silicone caulks. Plan your job in advance and always caulk seams or edges after painting. Compatible with Oil or Water Based topcoat paints.

Clean Up: XIM Reducto, XIM GON Cleaner or Mineral Spirits.

Potential Applications:
Building Material Plastic: More and more plastics are used in the building industry, including PVC sheeting and piping, vinyl shutters, vinyl molding and mill work, laminated Formica paneling and cabinets as well as fiberglass garage doors and other molded parts. First, remove old and loose paint then clean away wax, polish, grease, oil and other contaminants from the surface with a strong abrasive detergent. Wipe the surface with a cleaning solvent such as XIM GON Cleaner or xylene. Dry, then scuff sand the surface for maximum adhesion. Apply the XIM Bonder. Wait minimum of 2-3 hours and topcoat. Test for adhesion before starting the job.
Tile, Glazed Block and Brick, Porcelain: Decorative surfaces such as these can be restored and painted. First remove old paint and debris. Repair or patch any broken or damaged areas. Then clean away any wax, polish, grease, oil and other contaminants with a strong abrasive detergent. Wipe the surface with a cleaning solvent such as XIM GON Cleaner or xylene. For maximum adhesion scuff sand or etch the surface with XIM’s etching cream, Etch-I-M, rinse well to remove any etching residues and allow to dry. Apply the 400W ES White Bonder and allow to dry for a minimum of 2-3 hours, then apply the topcoat. Not recommended for sinks, tubs or shower areas where continuous water or hot water can be present. Note: where flexible seams or soft caulking are present, do not paint over with the 400W ES White. Always plan your job ahead and caulk after painting. Always caulk edges or seams that can trap and hold moisture and, therefore, become the source of coating failure. For exterior jobs - where high water contact is expected or where moisture or dew may accumulate, two coats of the top coat paint are recommended.
Non-Ferrous Metals: With 400W ES White Bonder you can get a long lasting, durable job when painting aluminum doors and window frames, aluminum and copper flashing and trim. Clean away all corrosion and any old paint, dirt, wax and grease. Wipe the surface with a cleaning solvent such as XIM’s GON Prep cleaner. Allow to dry then apply the 400W ES Bonder (only one coat is required) Allow the to dry for minimum of 2-3 hours, then apply the top-coat.

 
   

  48%

Details
 
SKU 2359660721
Quantity in stock 1000 item(s) available
Weight 2.00 lbs
Retail Price: $17.70
Our Price: $9.29

Options
 
Quantity

Add to cart
        


 

Send to friend

Your name: *
Your e-mail: *
Recipient's email: *

Type the characters you see in the picture. (If you do not see any picture here, please enable images in your web browser options and refresh this page):

Get a different code
The code is case-sensitive and must be entered exactly as above.

Send to friend
 

Recommended products list

Customers who bought this product also bought the following products:  
 

Popular Categories

Tapes

Spray Paint

Paint Brushes

Paint Tools

Caulk and Sealants

Paint Remover & Stripper

Hand Tools

Interior Paint

Exterior Paint

 

Popular Brands

ZAR

Valpar

Cabot

DAP

3M

ASM

 

Hammerite

Modern Masters

 

Best Seller Products

Duct Tape

Black Paint

White Paint

Blue Paint

Red Paint

Dap Plus

Chalk Board Paint

Gold Paint

Aluminum Paint

 
 

We accept major credit cards

credit cards logo
 
Home | Store | About Us | Search | Terms & Conditions | Privacy Statement | Contact Us | Directory | Site Map | News | Paint Store Blog
 
SEO by site SEO
 
 

CONNECT WITH US
Copyright 2005-2015 Paint Store - All Rights Reserved