Paint Store :: Shop by Brand :: UGL :: UGL 36012 ZAR 360 GLOSS ULTRA MAX OIL MODIFIED POLYURETHANE SIZE:QUART.

UGL 36012 ZAR 360 GLOSS ULTRA MAX OIL MODIFIED POLYURETHANE SIZE:QUART.

UGL 36012 ZAR 360 GLOSS ULTRA MAX OIL MODIFIED POLYURETHANE SIZE:QUART. 

ZAR® ULTRA MAX
A waterborne oil modified polyurethane which is an environmentally safe, revolutionary dual drying polyurethane. It dries by coalescing & oxygen cross-linking for a harder "through cure."

DESCRIPTION
ZAR ULTRA MAX Waterborne Oil Modified Polyurethane is an environmentally safe, clear wood finish specially formulated to protect and beautify floors, cabinets, furniture and woodwork. Self-leveling for a smooth finish .This fast drying, low-odor formula features superior hardness and mar resistance for outstanding wear and durability .
Natural ambering enhances wood tones. Dual Drying Technology makes the polyurethane dry by coalescing and oxygen cross-linking for a harder “through cure”. Child safe when dry. “Exotic Hardwood Approved”-Ideal for use on Teak, Brazilian Walnut and other exotic wood species.

SURFACE PREP
New Wood:
Sand smooth using fine sandpaper, vacuum sanding dust. Wipe clean using a tack-cloth or microfiber cloth. Do not use steel wool. If open-grained woods are to be filled, use a filler that does not contain stearates or waxes, such as ZAR Wood Patch.
Old Clear Finishes in Good Condition: Remove grease, dirt and wax. Sand lightly in the direction of the grain to remove any gloss. Do not use steel wool. Vacuum all sanding dust. Wipe clean using a tack-cloth or microfiber cloth. If the old finish contains wax or stearates, regardless of condition, remove completely. Clean dust with cloth dampened with paint thinner or mineral spirits.
Old Clear Finishes in Poor Condition, Lacquer or Shellac: Remove completely. Do not use steel wool. Sand and vacuum all sanding dust. Wipe clean using a tack-cloth or microfiber cloth.
If wood is to be stained, use ZAR Wood Stain or a water-based stain. Allow Wood Stain to dry a minimum of 3 hours. For water-based wood stains or oil-based wood stains other than ZAR, follow manufacturer’s drying directions.
NOTE: To ensure satisfactory results, always prepare a sample or test the product on an inconspicuous area to determine compatibility prior to completing the entire job. Do not apply over finishes containing stearates or aluminum oxide.

APPLICATION
Stir all sheens except ZAR ULTRA MAX Gloss Polyurethane thoroughly before and during application. Stirring is not required for ZAR ULTRA MAX Gloss Polyurethane finish. Do not shake! Apply straight from the can. DO NOT THIN. Use a clean synthetic fiber brush or use a foam pad. Do not apply with a roller. Apply thin coats at a rate of 400-500 sq.ft. per gallon in the direction of the grain. Too thick a coat may appear milky when dry. Do not over brush or trap air bubbles in the finish. Avoid over- brushing which may trap air bubbles in the finish and result in streaks. Make final pass of applicator a skimming stroke across the entire surface.
FLOOR APPLICATION
If floor is to be stained prior to applying ZAR ULTRA MAX, let stain dry according to manufacturer’s drying directions.
Areas with poor ventilation such as closed rooms, corners and hallways may take longer to dry. Prepare surface as above. Use a light weight T-Bar with a synthetic applicator or use a foam pad and spread the finish towards the opposite wall following the wood grain. Hold the applicator using a snowplow technique to maintain a wet edge. When approaching the end of a run, turn the applicator towards you and spread out excess material parallel to the wet edge. Feather out all turns. For maximum protection, apply 3 coats of ZAR ULTRA MAX. Allow floors to dry 24 hours before subjecting to light foot traffic; 3-5 days before moderate (normal) traffic or moving furniture. To avoid marring floor, lift and place furniture. One week is required before maximum resistance is achieved. Do not cover floors with rugs before one week has elapsed. If floor should become marred or scratched, simply sand lightly using fine sand paper, vacuum all sanding dust, wipe clean with a tack cloth or microfiber cloth and apply another coat to repair the finish.

DRYING
Dries to the touch in 30 minutes, can be recoated after 2 hours. Drying time will be affected by temperature, humidity and film thickness. If while sanding, sandpaper gums or surface feels tacky, extend drying time.

CLEAN-UP
Clean brushes and tools immediately after use with warm soapy water.

COVERAGE
Covers up to 400-500 sq.ft. per gallon. Apply 2 coats, for floors apply 3 coats.

 
   

  48%

Details
 
SKU 7994136012
Quantity in stock 1000 item(s) available
Weight 4.00 lbs
Retail Price: $32.23
Our Price: $16.92

Options
 
Quantity

Add to cart
        


 

Send to friend

Your name: *
Your e-mail: *
Recipient's email: *

Type the characters you see in the picture. (If you do not see any picture here, please enable images in your web browser options and refresh this page):

Get a different code
The code is case-sensitive and must be entered exactly as above.

Send to friend
 

Recommended products list

Customers who bought this product also bought the following products:  
 

Popular Categories

Tapes

Spray Paint

Paint Brushes

Paint Tools

Caulk and Sealants

Paint Remover & Stripper

Hand Tools

Interior Paint

Exterior Paint

 

Popular Brands

ZAR

Valpar

Cabot

DAP

3M

ASM

 

Hammerite

Modern Masters

 

Best Seller Products

Duct Tape

Black Paint

White Paint

Blue Paint

Red Paint

Dap Plus

Chalk Board Paint

Gold Paint

Aluminum Paint

 
 

We accept major credit cards

credit cards logo
 
Home | Store | About Us | Search | Terms & Conditions | Privacy Statement | Contact Us | Directory | Site Map | News | Paint Store Blog
 
SEO by site SEO
 
 

CONNECT WITH US
Copyright 2005-2015 Paint Store - All Rights Reserved