Paint Store :: Shop by Brand :: Drylok :: UGL 22113 DRYLOK CLEAR MASONRY TREATMENT LATEX BASE SIZE:1 GALLON.

UGL 22113 DRYLOK CLEAR MASONRY TREATMENT LATEX BASE SIZE:1 GALLON.

UGL 22113 DRYLOK CLEAR MASONRY TREATMENT LATEX BASE SIZE:1 GALLON. 

DRYLOK® MASONRY TREATMENT
DRYLOK® Masonry Treatment penetrates deep to seal and protect masonry against acids, alkalis, household cleaners, gasoline, oil and salt.

This VOC compliant, water base formula seals against dusting and retards spalling (surface cracking and pock marking) and weathering.

•A protective coating for masonry surfaces
•Prevents moisture damage, stops excessive dusting
•For brick, terrazzo, slate, concrete and other masonry surfaces
•Excellent primer for latex paint
•Application tools clean up with soap and water

 

DESCRIPTION
DRYLOK Masonry Treatment is a waterborne acrylic product that protects interior and exterior masonry surfaces from corrosive liquids and weathering. DRYLOK Masonry Treatment can also be used a primer for latex paint.
As A Sealer: DRYLOK Masonry Treatment penetrates deep to seal and protect masonry against acids, alkalis, household cleaners, gasoline, oil and salt. It also seals against dusting and retards spalling (surface cracking and pockmarking) and weathering. Treats chalking masonry paint, porous asbestos siding, sandblasted masonry and powdering mortar, before applying a latex paint.
As a Concrete Curing Membrane: When applied to freshly poured concrete, after the surface has set and excess water has been removed, DRYLOK Masonry Treatment will control water evaporation resulting in maximum concrete hardness. Allow 28 days before applying subsequent coatings.

SURFACE PREP
Remove all dirt, wax, dust, mildew, and loose or scaling material with a scraper, wire brush or stiff bristle brush. Grease and oil should be removed by scrubbing with a detergent in warm water. Rinse surface with clean water. Efflorescence (saltlike deposits) should be removed with DRYLOK Etch or Muriatic Acid according to manufacturer’s directions, then rinsed thoroughly with clean water. Cracks and holes should be filled with DRYLOK Concrete Patch.

APPLICATION
Apply only when surface temperature is above 40°F. Apply full strength with brush, pad applicator, garden sprayer or squeegee. Spread evenly - do not allow puddles or a heavy surface film to occur.
One coat is generally sufficient for most surfaces. If a second coat is required (extremely porous surfaces) allow 6 hours between coats. Additional coats will cause surface to be slippery when wet.
On light-colored surfaces, some darkening may take place; test in an inconspicuous area to be sure darkening does not occur. May be applied to surfaces previously coated with a similar treatment. For best results, test a small area for proper adhesion prior to coating entire surface.

THINNING
When applied over flagstone, slate, terrazzo or dense, smooth concrete, thin DRYLOK Masonry Treatment with equal parts of clean, lukewarm water. In addition, light colored concrete may darken unevenly due to variations in porosity. To minimize color variations, thin with water 1 to 1 and test on small area to see final effect.

USED AS A PRIMER
DRYLOK Masonry Treatment will solidify the surface for painting when applied over powdery surfaces such as chalking masonry paint, porous asbestos siding, sand blasted masonry and powdering mortar. It is also ideal for use as a PRIMER-SEALER under latex, alkyd or polyurethane concrete floor paints or carpeting. For self adhesive floor tiles, check with tile manufacturer for adhesion compatibility.

DRYING
Allow 6 hours before subjecting to light foot traffic and 24 hours before subjecting to heavy traffic. During periods of high humidity and/or cool temperatures, allow 24 hours before subjecting to light foot traffic.

COVERAGE
One gallon of DRYLOK Masonry Treatment will cover up to 400 square feet depending on surface porosity.

CLEAN-UP

Clean tools with soap and water.

MAINTENANCE
None required. Because DRYLOK Masonry Treatment prevents the penetration of dirt, moisture, etc., coated surfaces are easy to clean.

 
   

  47%

Details
 
SKU 7994122113
Quantity in stock 1000 item(s) available
Weight 14.00 lbs
Retail Price: $33.50
Our Price: $17.59

Options
 
Quantity

Add to cart
        


 

Send to friend

Your name: *
Your e-mail: *
Recipient's email: *

Type the characters you see in the picture. (If you do not see any picture here, please enable images in your web browser options and refresh this page):

Get a different code
The code is case-sensitive and must be entered exactly as above.

Send to friend
 

Detailed images

UGL 22113 DRYLOK CLEAR MASONRY TREATMENT LATEX BASE SIZE:1 GALLON.
 

Recommended products list

Customers who bought this product also bought the following products:  
 

Popular Categories

Tapes

Spray Paint

Paint Brushes

Paint Tools

Caulk and Sealants

Paint Remover & Stripper

Hand Tools

Interior Paint

Exterior Paint

 

Popular Brands

ZAR

Valpar

Cabot

DAP

3M

ASM

 

Hammerite

Modern Masters

 

Best Seller Products

Duct Tape

Black Paint

White Paint

Blue Paint

Red Paint

Dap Plus

Chalk Board Paint

Gold Paint

Aluminum Paint

 
 

We accept major credit cards

credit cards logo
 
Home | Store | About Us | Search | Terms & Conditions | Privacy Statement | Contact Us | Directory | Site Map | News | Paint Store Blog
 
SEO by site SEO
 
 

CONNECT WITH US
Copyright 2005-2015 Paint Store - All Rights Reserved