Paint Store :: Shop by Brand :: Flood :: FLOOD FLD140 SWF-SOLID PASTEL BASE 250 VOC SIZE:1 GALLON.

FLOOD FLD140 SWF-SOLID PASTEL BASE 250 VOC SIZE:1 GALLON.

FLOOD FLD140 SWF-SOLID PASTEL BASE 250 VOC SIZE:1 GALLON. 

Flood SWF-SOLID Color Wood Finish is a premium finish for new wood and for recoating old applications. SWF-SOLID is fortified with E-B Emulsa-Bond to provide unsurpassed adhesion to vertical and horizontal exterior substrates where other products ultimately fail or require extensive preparation and priming. SWF-SOLID blends acrylic and urethane technologies to provide reliable adhesion, abrasion-resistance and flexibility. SWF-SOLID delivers high traffic performance on deck surfaces and is the perfect choice for long- asting beauty on siding. SWF-SOLID is guaranteed not to peel or blister.

BASIC USES
• For exterior use only
• New or weathered exterior wood
• Previously coated exterior surfaces
• Siding (new or weathered, including: untreated solid wood, primed and previously finished fiber cement board and plywood, including T1-11, and aluminium)
• Decks, docks and other horizontal surfaces including PTW, cedar, redwood, hardwoods and composite decking
• Fences and other vertical surfaces
• Trim boards and outdoor wood furniture
• Weathered vertical masonry including stucco, painted block, EIFS, etc.

SURFACE PREPARATION
GENERAL DIRECTIONS:
1. Surfaces to be coated should be clean and dry before applying SWF-SOLID Solid Color Wood Finish.
2. Sand, scrape or wire brush to remove all loose flaking or peeling finish
3. Pressure wash to remove excess dirt, chalk, oxidation and other surface contamination.
4. Mildew - A mildew-resisting component has been incorporated into this product to make its dry film mildew resistant, however, no coating is mildew proof. Before coating, remove mildew by scrubbing the surface with a mixture of four ounces of non-ammonia detergent (TSP), one quart of household bleach and three quarts of water. Allow this solution to remain on the surface for 10-15 minutes, then rinse thoroughly. Repeat until mildew is completely removed. Wear protective glasses or goggles and waterproof gloves when using this solution. Quickly wash off mixture that touches your skin. Allow 2-3 days dry time after cleaning before finishing or when wood has a moisture content of <15%.

NEW WOOD SURFACES:
The ideal time to finish new wood is one to three months after installation. Many new wood surfaces can have a hard, shiny condition called mill glaze that prevents maximum penetration and adhesion of a finish. All new wood, especially decks, should be prepared with Flood Wood Stripper or FloodPro® Stripper/Cleaner to reduce mill glaze, remove natural wood chemicals and other factory applied sealers to open wood and allow maximum penetration.

WEATHERED WOOD OR PREVIOUSLY COATED SURFACES:
Follow "General Directions" for surface prep.

HIGH EXTRACTIVE WOODS: (i.e. red cedar, redwood)
"Extractives" or tannins are natural wood chemicals that give wood its color. These chemicals can "bleed" into a topcoat and cause discoloration of the finish. Use Flood Wood Cleaner or Flood Dekswood® (diluted with water from 1:1 for redwood to 4:1 for cedar) to remove tannin stains and clean the surface prior to coating. To prevent tannin bleed, use an oil-based exterior stain blocking primer, designed to seal exterior wood to control tannin and knot bleeding, prior to application. Alternatively, apply the first coat of Flood SWF-SOLID Wood Finish. Allow the first coat to cure 7 days prior to application of the second coat.

COLOR SELECTION
• Before starting job, test your color choice on a small area
• Buy sufficient product for the whole job and box or intermix all product together before staining to avoid color variance
• DO NOT USE TINT BASES UNTINTED
NOTE: Custom tint using colorants that are approved for exterior use only.

APPLICATION TOOLS
• Apply FloodPro Solid Color Finish with a synthetic brush, 3/8" - 3/4" nap, tight knit synthetic roller cover, stain brush/pad or airless sprayer
• Spray equipment .015 - .019 fluid tip/1,500-2,100 psi fluid pressure

APPLICATION
CAUTION: Surfaces are slippery when wet. Use caution when walking on wet surfaces during application.
1. Clean as directed under "Surface Preparation".
2. Cover everything you do not wish to coat including plants and shrubs.
3. Apply between 50º and 80º F. Do not apply in direct sunlight, on hot
surfaces or if cold and/or wet weather is expected within 48 hours.
4. Mix product thoroughly before and during application. Do not thin.
5. For color uniformity, use a larger container (ex. 5 gallon bucket) to intermix all product to be used in one area.
6. Apply an even coat of SWF-SOLID Color Wood Finish avoiding
heavy application.
7. Always work the entire length of a deck board or horizontal siding to a logical break, such as a window or door frame.
8. Vertical siding should be coated from top to bottom.
9. If spraying on product, always back brush or back roll material to provide maximum substrate coverage, penetration and uniform appearance.
10.If additional coats are required, it may be applied 3-4 hours after initial application.

COVERAGE RATES
• Smooth/moderately porous surfaces: 350 - 400 sq. ft/gal
• Rough/weathered/porous surfaces: 250 - 350 sq. ft/gal
NOTE: Actual coverage rates may vary depending upon substrate type and/or conditions as well as application method.

MAINTAINING SWF-SOLID COLOR FINISH
Surfaces with harsh exposure to sun, weather or foot traffic will show wear more quickly than other areas - if this happens, clean affected areas and recoat as necessary.

CLEANUP & STORAGE
• Cleanup with soap and water.
• If SWF-SOLID is allowed to dry on tools, remove with
paint remover.
• Store unused portion in a sealed container to prevent gelling.
• KEEP FROM FREEZING

 
   

  47%

Details
 
SKU 1027314015
Quantity in stock 1000 item(s) available
Weight 15.00 lbs
Retail Price: $42.13
Our Price: $22.12

Options
 
Quantity

Add to cart
        


 

Send to friend

Your name: *
Your e-mail: *
Recipient's email: *

Type the characters you see in the picture. (If you do not see any picture here, please enable images in your web browser options and refresh this page):

Get a different code
The code is case-sensitive and must be entered exactly as above.

Send to friend
 

Detailed images

FLOOD FLD140 SWF-SOLID PASTEL BASE 250 VOC SIZE:1 GALLON.
 

Recommended products list

Customers who bought this product also bought the following products:  
 

Popular Categories

Tapes

Spray Paint

Paint Brushes

Paint Tools

Caulk and Sealants

Paint Remover & Stripper

Hand Tools

Interior Paint

Exterior Paint

 

Popular Brands

ZAR

Valpar

Cabot

DAP

3M

ASM

 

Hammerite

Modern Masters

 

Best Seller Products

Duct Tape

Black Paint

White Paint

Blue Paint

Red Paint

Dap Plus

Chalk Board Paint

Gold Paint

Aluminum Paint

 
 

We accept major credit cards

credit cards logo
 
Home | Store | About Us | Search | Terms & Conditions | Privacy Statement | Contact Us | Directory | Site Map | News | Paint Store Blog
 
SEO by site SEO
 
 

CONNECT WITH US
Copyright 2005-2015 Paint Store - All Rights Reserved